[email protected] Free Shipping On Orders Over $40

Shopping Cart

TC118S Dual Motor Driver Module – Low-Level Trigger Control for DC Motors and Small Robotics

The HS-F09C variant is the Dual Low-Level Trigger motor-driver option on the L9110S dual motor driver product page. It is designed for simple two-channel DC motor control, small robot platforms, fan drivers, vibration motors, and STEM experiments where a microcontroller needs to switch motor direction or speed without driving the motor directly.

The current product page includes both a high-level L9110S option and this low-level trigger TC118S option, so verify the selected variant before wiring. HS-F09C is especially useful when your controller logic or project circuit expects active-low control. It can be paired with the ELAB Nano V3, an UNO R3 Prototype Expansion Board, and visual indicators such as the RGB Full Color LED Module.

Motor drivers must be wired with careful attention to motor supply, logic input polarity, common ground, and current draw. Start with unloaded motors on the bench, then verify temperature rise and peak current before installing the module in a robot chassis.

Technical Specifications

Parameter Value
SKU HS-F09C
Variant Dual Low-Level Trigger (TC118S)
Product Type Dual DC motor driver module
Channels 2 motor channels
Trigger Logic Low-level trigger for HS-F09C variant
Typical Motor Supply Follow module label and motor voltage requirements
Control GPIO direction control and PWM speed control where supported
Applications Small robots, fans, pumps, vibration motors, STEM vehicles
Important Wiring Common ground between motor supply and microcontroller
Protection Note Keep motor current within module and IC limits

Board Layout & Label Guide

  • Motor Output A – Connect to one DC motor winding.
  • Motor Output B – Connect to the second DC motor or second channel output.
  • VCC / VM – Motor power input; match the motor voltage requirement.
  • GND – Shared ground for motor power and controller logic.
  • Input Pins – Low-level trigger control inputs for direction and enable behavior.
  • PWM Input – Use a PWM-capable controller output for speed control when wired appropriately.
  • Variant Note – HS-F09C is not the high-level trigger variant; software logic may need inversion.
  • Thermal Note – Stop testing if the driver becomes hot under load.

Application Scenarios

1. Arduino One-Motor Direction Test

Toggle a motor forward and reverse using two control inputs.

const int in1 = 5;const int in2 = 6;void setup() { pinMode(in1, OUTPUT); pinMode(in2, OUTPUT);}void loop() { digitalWrite(in1, LOW); digitalWrite(in2, HIGH); delay(1000); digitalWrite(in1, HIGH); digitalWrite(in2, LOW); delay(1000);}

2. PWM Speed Ramp

Ramp motor speed with PWM while keeping direction fixed.

const int pwmPin = 5;const int dirPin = 6;void setup() { pinMode(pwmPin, OUTPUT); pinMode(dirPin, OUTPUT); digitalWrite(dirPin, LOW);}void loop() { for (int speed = 0; speed <= 255; speed++) { analogWrite(pwmPin, speed); delay(10); }}

3. Two-Wheel Robot Drive

Drive left and right motors for a simple robot platform.

const int leftA = 3;const int leftB = 4;const int rightA = 5;const int rightB = 6;void setup() { pinMode(leftA, OUTPUT); pinMode(leftB, OUTPUT); pinMode(rightA, OUTPUT); pinMode(rightB, OUTPUT);}void loop() { digitalWrite(leftA, LOW); digitalWrite(leftB, HIGH); digitalWrite(rightA, LOW); digitalWrite(rightB, HIGH); delay(1500);}

4. ESP32 Fan Driver

Use an ESP32 PWM output to control a small DC fan through the driver.

const int fanPin = 18;void setup() { ledcAttach(fanPin, 20000, 8);}void loop() { ledcWrite(fanPin, 180); delay(5000); ledcWrite(fanPin, 0); delay(5000);}

Packing List

  • 1 x TC118S Dual Low-Level Trigger Motor Driver Module

FAQ

Q: What is HS-F09C?
A: It is the Dual Low-Level Trigger (TC118S) variant on this motor driver product page.

Q: Can it drive two motors?
A: Yes, it is a dual motor driver module.

Q: Why does my logic seem inverted?
A: HS-F09C is a low-level trigger variant, so active logic may be opposite of high-level modules.

Q: Can I use PWM?
A: Yes, PWM can be used for speed control when connected to the correct input.

Q: Do I need common ground?
A: Yes, share ground between controller and motor driver.

Q: Can it drive large motors?
A: No, use it only within the module’s current and thermal limits.

Q: What should I test first?
A: Test direction and current with the motor unloaded.

Q: Why does the board heat up?
A: Motor current may be too high, the motor may be stalled, or supply voltage may be unsuitable.

Add a Review

Your email address will not be published. Required fields are marked *

Related Products